Deutsch
English
Linear magnetic dirt trap filter with brass bowl and threaded ends plug / plug UNI ISO 228.
which mainly consist of sand and rust and are used in heating and cooling system circuits
available. Due to their effective and constant effect, the magnetic filters capture all
contaminants present in the system and preventing them from circulating through the system,
causing wear and tear on other system components, mainly circulators and
Heat exchangers, are avoided. During operation, the continuous flow of liquid
through the filter installed in the system gradually leads to the complete elimination of sludge and
dirt. Linear magnetic filters filter the heating system fluid thanks to the dual action of the
Stainless steel filter mesh and neodymium magnets. Thanks to the special structure of the filter body
and the effect of the filter net, the impurities sink to the bottom of the brass bowl.
Here, strong magnets attached to the outer loop create a magnetic field,
that can block the iron particles present in the liquid, while other
Impurities can deposit on the bottom of the filter.
damage, impairing the correct tightness and proper operation
In order to facilitate cleaning and maintenance, it is recommended to use shut-off valves
to be installed before and after the filter.
The tightening torque must guarantee the correct tightness without damaging the magnetic filter or the fittings.
Check the specifications and / or the requirements of the country of installation.
but also on making a product that is easy to clean.
In just a few simple steps and without complicated downtime, the functions of the filters are fully restored.
Maximum temperature: 95°C
Maximum operating pressure: working limits at 10 bar
Connections: 3/4" inner thread UNI ISO 228
1" external thread UNI ISO 228
Particle separation capacity: 5 μm
Description / material:
Housing: CW617N-EN12165 nickel-plated brass
Cup: CW617N-EN12165 Nickel-plated brass
Filter cartridge: Inox AISI 304
O-rings: nitrile rubber NBR
Empty ball valve: CW617N-EN12164 chrome-plated brass
Magnetic ring: PA 6 black
Magnets: Neodymium 3x12,000 GAUSS
Available with or without side connector UNI ISO 228.
The linear magnetic sludge removers are installed to remove particles,
which mainly consist of sand and rust and are used in heating and cooling system circuits
available. Due to their effective and constant effect, the magnetic filters capture all
contaminants present in the system and preventing them from circulating through the system,
causing wear and tear on other system components, mainly circulators and
Heat exchangers, are avoided. During operation, the continuous flow of liquid
through the filter installed in the system gradually leads to the complete elimination of sludge and
dirt. Linear magnetic filters filter the heating system fluid thanks to the dual action of the
Stainless steel filter mesh and neodymium magnets. Thanks to the special structure of the filter body
and the effect of the filter net, the impurities sink to the bottom of the brass bowl.
Here, strong magnets attached to the outer loop create a magnetic field,
that can block the iron particles present in the liquid, while other
Impurities can deposit on the bottom of the filter.
The filter flow direction is always indicated by markings on the valve body (arrows, ...).
Suitable for solar, heating systems.
damage, impairing the correct tightness and proper operation
In order to facilitate cleaning and maintenance, it is recommended to use shut-off valves
to be installed before and after the filter.
The magnetic filter and the connectors must be connected to the system using suitable devices become.
The tightening torque must guarantee the correct tightness without damaging the magnetic filter or the fittings.
After completing the installation, it is necessary to replace the seals in accordance with the technical
Check the specifications and / or the requirements of the country of installation.
The design of the magnetic dirt trap filter has not only focused on particle separation efficiency,
but also on making a product that is easy to clean.
In just a few simple steps and without complicated downtime, the functions of the filters are fully restored.
Technical characteristics:
Maximum temperature: 95°C
Maximum operating pressure: working limits at 10 bar
Connections: 3/4" inner thread UNI ISO 228
1" external thread UNI ISO 228
Particle separation capacity: 5 μm
Description / material:
Housing: CW617N-EN12165 nickel-plated brass
Cup: CW617N-EN12165 Nickel-plated brass
Filter cartridge: Inox AISI 304
O-rings: nitrile rubber NBR
Empty ball valve: CW617N-EN12164 chrome-plated brass
Magnetic ring: PA 6 black
Magnets: Neodymium 3x12,000 GAUSS
You can find the data sheet in "Media". Link to the product: https://www.tiemme.com/deu/contabilizzazione/3149_contabilizzazione-det_8149.php